[creation site internet] [creation site web] [logiciel creation site] [Home]
[Page 1]
[Page 1]
[Page 3]
[Page 2]
[Page 2]
[Page 1]
[Page 1]
[Page 1]
[Page 2]
[Page 2]
[Page 5]
[Page 5]
[Page 8]
[Page 2]
[Page 6]
[]
[Page 1]


Call 0417 965 322


P485


OEM UPGRADE ALARM SYSTEM























Introduction


Dynamco has upgraded the OE Upgrade, higher current immobilisation and multiple plug-in sensors available; to name only a few of the improvements. This Australian Standards Upgrade Alarm transforms an Original Equipment vehicle keyless entry system into an Australian Standards alarm system. The system is operated by the vehicles original equipment remote and has Entry point protection of doors, boot and bonnet with an intelligent glass break sensor. Audible warning is achieved via an Australian Standards 115dB battery back up siren, visually via the vehicle indicators and via a dash mounted red LED. The system has status / diagnostic reporting. The system can provide two additional circuits of immobilisation


Proudly Australian

Designed and engineered in Perth, Western Australia

Operation


Arming procedure while ignition is off

The system will arm immediately when the lock button of the remote control supplied by the car manufacturer is pressed

Disarming procedure

Press the unlock button of the remote control supplied by the car manufacturer

Auto Arming

System will auto-arm only if the car has a automatic re-locking feature

Immobilisation


Dual Immobilisation Circuits

The system features two independent 30 Amp rated, normally open immobilisation circuits, which break engine critical signals in the vehicle. Starter motor, fuel pump, fuel injection, main ignition are commonly immobilised circuits

Safety circuitry in case of power failure

System sources alternate power from ignition if main power is lost

Third circuit of immobilisation (optional)

Additional immobilisation circuits can be added to conform with insurance company requirements

Component protection against harsh road conditions

All relays are fully encapsulated to provide protection against dust and moisture

Wiring


Security wiring

All cables extending from the control module are black and same diameter. Identifying wire tags are removed by the installer during installation of the system

Plug and play for service

Designed to allow easy access for service technicians. Plugs and sockets are located inside the main control module to protect against access by thieves

Security housing

Connector plug is enclosed within module case to prevent access by thief

Stealth wiring

Cutting any immobilisation wiring will still leave the car secure. Bypassing security is not possible by simply removing the system from the vehicle

Override


Emergency Personal Identification Number (PIN) override

If the valid controller are lost, stolen or broken, the user by over-ride the system by enter the secret four digits via the ignition switch 

Alterable PIN

A factory programmed PIN comes standard with each system. It is recommended the owner of the system changes the PIN to a new, easily remembered number 

High security keys and lock

Disable siren sound when vehicle is taken in for service

PIN card

A record of the factory programmed override PIN is supplied on handy wallet sized card

Visual Output


Super bright red dash LED

This LED flashes to inform user when system is armed. The LED is mounted on the driver's side dash and is visible from outside the window

Arm/Disarm confirmation

System flashes car indicators when arming or disarming 

Alarm illumination

System flashes car indicators when thief triggers alarm

Trigger diagnostics

System will flash indicators to report the last triggered circuit

Audio Output


Large battery backup siren

AS/NZS 3749.1:2003 Class A approved 115dB siren, sounds even if battery terminals are disconnected from vehicle battery

Negative siren output

Can be used to trigger car horn relay or siren

Arm/Disarm confirmation

System sounds a siren when arming and disarming 

Intrusion Detection


Doors, bonnet and boot monitoring

Triggers alarm system if intruder opens any protected entry point in vehicle

False alarm prevention

All circuits detected as triggered when arming system will automatically be isolated until trigger resets

Sensor sockets

Compatible sensors plug straight into main pcb

Audio glass breakage detection

Uses the sound of the breaking glass to trigger (not vibration) GBS-4XR.

Accepts plug-in Ultra-sonic sensor

Sensor produces a 40KHz sound wave and measures echo to detect intruder,  ACC-001.

Accepts plug-in single zone microwave sensor

Sensor produces a microwave field to detect intruder,  ACC-003.

Accepts plug-in dual zone microwave sensor

Sensor produces two microwave fields, exterior field to sound siren as warning, interior to trigger alarm in full,  ACC-004.

Accepts plug-in single stage shock sensor

Sensor measures vibration subjected to vehicle to detect intruder,  SEN-002.

Accepts plug-in two stage shock sensor

Sensor measures two levels of shock, soft shock to sound siren as warning, heavy shock to trigger alarm in full,  SEN-006.

Compatible with tilt sensor

Sensor measures vehicle angle with respect to earth, triggers if angle changes - no response to vibration  SEN-004.

Millivolt or Voltage drop protection

Alarm monitors battery voltage, triggers if voltage drop due to courtesy light switched from off to on (opening boot etc) 

Specifications


Current draw

<10mA average while armed

<250mA disarm (and for no more than 39 seconds after ignition is switched off)

Wide Operating voltage

Operating voltage +9VDC to +15VDC

Operating temperature

-20 degrees to +85 degrees for equipment designed to be installed within vehicle cabin

Operating temperature

-20 degrees to +105 degrees for equipment designed to be installed inside engine compartment

Polarity protection

The system circuitry is design to protect itself against accidental battery polarity reversal. This can happen when replacing the vehicle battery

Independent indicator power fuse

System uses independent fuse to power indicators, ensures short circuit in indicator circuit does not affect system operation

Suitable for models of these manufacturers

Audi, Alfa Romeo, BMW, Chrysler, Ford, Holden, Honda, Hyundai, Kia, Landrover, Mazda, Mercedes, Mitsubishi, Nissan, Peugeot, Proton, Renault, Subaru, Suzuki, Toyota, Volvo & VW

Short circuit protection

The power supply wire to the system is protected against an internal fault within the system

Convenience Functions


Electric window closer

Provides signals used by electric window closers, system will close all electric windows when armed by remote control

Full diagnostic report

Remove and insert main power fuse to receive report of last three triggers

Printed Material


Installation Guide

Generic instructions on how to fit the system, it's features and limitations. Open 4WAY version.

User Guide

Informs the end-user of the system's functions, features and limitations. Open - User guide.

Warranty


Manufacturers warranty on Control module

Guarantees control module is free from manufacturing defects for 24 months from time of purchase

Manufacturers warranty on Siren

Guarantees siren is free from manufacturing defects for 12 months from time of purchase

Standards Compliance


Australian Standard for Intruder alarm systems - Road vehicles - Performance requirements

AS/NZS 3749.1:2003 Class A - Australian Standards website.

Manufactured in ISO9001 facility

Built within world standard production facility

AS/NZS 3749 sundry standards of compliance (or parts thereof)

AS1217 - Acoustics - Determination of sound power levels of noise sources

AS1259 - Acoustics - Sound level meters

AS1939 - Degrees of protection provided by enclosures for electrical equipment (IP Code)

AS3350 - Safety of household and similar electrical appliances

AS4268 - Radio equipment and systems - Short range devices

AS/NZS3749 - Intruder alarm systems - Road vehicles

AS/NZS61000 - Electromagnetic compatibility (EMC)

CISPR 22 - Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement

ASTM B117 - Standard practice for operating salt spray (fog) apparatus

ISO512 - Road vehicles - Sound signalling devices - Technical specifications

ISO7637 - Road vehicles - Electrical disturbance by conduction and coupling

IEC61000 - Electromagnetic compatibility (EMC)



  

Powered by WebCreator.

   © Copyright Auto Arms 2012. All rights reserved.